testo 312-4 - Przyrząd do pomiaru różnicy ciśnień do 200hPa

Miernik różnicy ciśnień testo 312-4

PLN 2 097,00 PLN 2 579,31 z VAT
Nr katalogowy 0632 0327
Zapytaj o produkt

Opis produktu

Miernik do przeprowadzania wszystkich koniecznych prób instalacji gazowych, jak również wodnych. Bezpieczny w użyciu dzięki elastycznym przewodom C-Flex o wysokiej odporności.
Rejestracja pomiarów oraz analiza danych za pomoca programu Easyheat (opcja) z funkcjami graficznymi.

Dane techniczne

Dane techniczne

Pamięć

ok. 25.000 Odczyty

Wymiary

219 x 68 x 50 mm

Sonda ciśnienia

Dane techniczne

Zakres pomiarowy

0 200 hPa

Dokładność

±0,03 hPa (0 +3 hPa)
±1,5% wartości pomiaru (+3,1 +40 hPa)
±2 hPa lub ±1% wartości końcowej (+41 +200 hPa)

Rozdzielczość

0,01 hPa

Ciśnienie

Dane techniczne

Zakres pomiarowy

0 25 bar

Dokładność

±0,6% wartości końcowej (0 10 bar)
±0,6% wartości końcowej (>10 25 bar)

Rozdzielczość

10 hPa

Pressure tests on gas pipes (load test)

The technical regulation for gas installations (in short: TRGI) is a binding and at the same time important regulation for skilled tradespeople. The TRGI governs how gas installations are to be planned, designed, serviced and maintained. This applies to all gas installations. This regulation is taken care of by the German Association for Gas and Water (DVGW). The TRGI 2008 is the current version. Amongst other things, this states that gas pipes are to be tested according to the construction phase (basic shell, completion and repairs). Load testing is one of the checks that plays a role in the application stated here: in this process, the material of a gas pipe is tested for stability and the connections for service life; this takes place prior to plastering over or concealment of the gas pipes. During load testing, the newly installed pipe, without fittings or gas appliances, is put under 1 bar pressure. The testing medium is air or inert gas. There must be no pressure drop detected during the test, which lasts at least 10 minutes.

Pressure tests on gas pipes (leak, load test)

The technical regulation for gas installations (in short: TRGI) is a binding and at the same time important regulation for skilled tradespeople. The TRGI governs how gas installations are to be planned, designed, serviced and maintained. This applies to all gas installations. This regulation is taken care of by the German Association for Gas and Water (DVGW). The TRGI 2008 is the current version. Amongst other things, this states that gas pipes are to be tested according to the construction phase (basic shell, completion and repairs). The following checks in particular play a role in the application stated here:

Load test
In this process, the material is tested for stability and the connections for service life; this takes place prior to plastering over or concealment of the gas pipes. During load testing, the newly installed pipe, without fittings or gas appliances, is subjected to 1 bar pressure. The testing medium is air or inert gas. There must be no pressure drop detected during the test, which lasts at least 10 minutes.

Leak test
This test is for checking the pipe for leaks, with fittings and without gas appliances. The measuring instrument must not register any drop in pressure during the minimum 10-minute testing period (depending on the system volume); the test pressure is 150 mbar (previously 110 mbar).

Pressure measurements on burners

Checking the gas pressure on burners is one of the standard measurements during services of domestic heating systems. This involves measuring the gas flow pressure and gas resting pressure of the system. The flow pressure, also called supplied pressure, refers to the gas pressure of the flowing gas and resting pressure of the static gas. If the flow pressure for gas boilers is slightly outside the 18 to 25 mbar range, adjustments must not be made and the appliance must not be put into operation. If the burner is nevertheless put into operation, it will not be able to function properly and, when the flame is generated, small explosions will occur and ultimately malfunctions; the burner will therefore shut down and the heating system will fail.

Pressure tests on water pipes

According to the legal regulations of DIN EN 806-4, DIN 1988-7 and DIN 1610, drinking and waste water pipes are to be tested for leaks before being put into service by means of a pressure test with air, inert gas or water; they are also to undergo load testing with air or inert gas. However, for reasons of hygiene, it is best if the pipes remain dry until shortly before commissioning and do not undergo a leak test using water. A pressure test with air is also recommended to prevent metallic materials from corroding. The pressure test is split into two pressure-related parts where test pressure and time depend on the objective (load or leak). Leaks can usually be heard very quickly. If it is difficult to locate the leaks, the usual auxiliary tools and materials for gas pipes are used (spraying or brushing on foaming solutions).

Pressure tests on gas pipes (leak test with external high pressure probe, load test)

The technical regulation for gas installations (in short: TRGI) is a binding and at the same time important regulation for skilled tradespeople. The TRGI governs how gas installations are to be planned, designed, serviced and maintained. This applies to all gas installations. This regulation is taken care of by the German Association for Gas and Water (DVGW). The TRGI 2008 is the current version. Amongst other things, this states that gas pipes are to be tested according to the construction phase (basic shell, completion and repairs). The following checks in particular play a role in the application stated here:

Load test
In this process, the material is tested for stability and the connections for service life; this takes place prior to plastering over or concealment of the gas pipes. During load testing, the newly installed pipe, without fittings or gas appliances, is subjected to 1 bar pressure. The testing medium is air or inert gas. There must be no pressure drop detected during the test, which lasts at least 10 minutes.

Leak test
This test is for checking the pipe for leaks, with fittings and without gas appliances. The measuring instrument must not register any drop in pressure during the minimum 10-minute testing period (depending on the system volume); the test pressure is 150 mbar (previously 110 mbar).

Temperature measurements on radiators

When measuring temperatures on radiators, the flow and return temperature are recorded in particular and assessed by the tradespeople. The flow temperature is defined as the temperature of the thermal transfer medium (e.g. water) that the system is supplied with. The temperature of the medium flowing out of the system is correspondingly called the return temperature. To prevent losses within the heat distribution system and achieve a better level of efficiency, spot recording of flow and return temperatures is necessary. Implementation of relevant measures ultimately leads to hydraulic adjustment on the basis of knowledge about the flow and return temperatures. This defines a procedure with which every radiator or heating circuit of a flat radiator within a heating system is supplied at a set flow temperature with the precise amount of heat needed to achieve the ambient temperature required for the individual rooms. Flawed operating conditions will result in considerable excess consumption of electricity and heating energy. The German Energy Saving Regulation (EnEV) requires hydraulic adjustment for systems being set up or overhauled for this very reason.

Katalogi

Do pobrania Typ Rozmiar

Product brochure testo 312-2/-3/-4

PDF

690,7 kB

Pobierz

Akcesoria

Nazwa produktu Nr katalogowy

Wąż połączeniowy, pojedynczy, średnica: 4/6 mm, dł. 50 cm, bez adaptera połączeniowego

0554 0449

PLN 65,00
z VAT PLN 79,95

0554 3172

0554 3173

test stozkowy 1/2" do podłączenia zestawu testującego do rur gazowych 16 32 mm

0554 3151

Test stożkowy 3/4" do podłączenia zestawu testuącego do rury gazowej 32-54 mm

0554 3155

0554 3156

0554 3161

Ogranicznik

0554 3162

LW 6 wąż połączeniowy

0554 3158

Sprej do detekcji wycieków gazów, do pryskania na rurach gazowych. pokazuje punkty wycieków

0554 3166

Zasilacz

0554 1143

PLN 531,00
z VAT PLN 653,13

Pompa testowa

0554 3157

9V akumulator do miernika

0515 0025

PLN 55,00
z VAT PLN 67,65

Ładowarka do akumulatora 9V

0554 0025

PLN 46,00
z VAT PLN 56,58

Szybka bezprzewodowa drukarka Testo, 1 rolka papieru i 4 baterie AA

0554 0549

TopSafe (walizka ochronna)

0516 0446

PLN 291,00
z VAT PLN 357,93

0516 3121

0638 1743

Poziom wysokiego ciśnienia 3/8" i 3/4"

0554 3163

Poziom wysokiego ciśnienia 1/2" i 1"

0554 3164

Kabel połączeniowy

0430 0143

PLN 253,00
z VAT PLN 311,19

Pełna wersja EasyHeat (oprogramowanie PC)

0554 3332

Kabel RS232

0409 0178

PLN 257,00
z VAT PLN 316,11

Formularz kontaktowy

22 863 74 22
Kontakt

Oddzwonimy do Państwa

Oddzwonimy do Państwa